| Start |  |
Contact | |
Back |
|
||||
1510: Cylindrical Double Nut, Ground Thread, Nominal Diameter 8 mm |
||||
|
Item No. |
Specifications |
|||||
|
Lead1) |
Nominal Diameter |
No. of circuits2) |
Travel |
Load capacity |
||
|
dyn.3) |
stat. |
|||||
|
P
|
dN
|
i
|
Lv
|
Ca
|
C0a
|
|
|
mm
|
mm
|
mm
|
N
|
N
|
||
|
1510/0,5.8.145.170 |
0,5 |
8 |
2 |
100 |
220 |
270 |
|
1510/1.8.145.170 |
1 |
8 |
2 |
100 |
630 |
820 |
|
1510/2.8.145.170 |
2 |
8 |
2 |
100 |
1400 |
1400 |
|
1510/2,5.8.145.170 |
2,5 |
8 |
2 |
100 |
1400 |
1400 |
|
1510/0,5.8.245.270 |
0,5 |
8 |
2 |
200 |
220 |
270 |
|
1510/1.8.245.270 |
1 |
8 |
2 |
200 |
630 |
820 |
|
1510/2.8.245.270 |
2 |
8 |
2 |
200 |
1400 |
1400 |
|
1510/2,5.8.245.270 |
2,5 |
8 |
2 |
200 |
1400 |
1400 |
|
Item No. |
|
||
|
4) max. preload |
max. |
max. |
|
|
Fpr
max
|
Fmax
|
Tpr0
|
|
|
N
|
N
|
N
cm
|
|
|
1510/0,5.8.145.170 |
15 |
10 |
0,7-1,5 |
|
1510/1.8.145.170 |
30 |
20 |
0,7-1,5 |
|
1510/2.8.145.170 |
50 |
40 |
0,7-1,5 |
|
1510/2,5.8.145.170 |
50 |
40 |
0,7-1,5 |
|
1510/0,5.8.245.270 |
15 |
10 |
0,7-1,5 |
|
1510/1.8.245.270 |
30 |
20 |
0,7-1,5 |
|
1510/2.8.245.270 |
50 |
40 |
0,7-1,5 |
|
1510/2,5.8.245.270 |
50 |
40 |
0,7-1,5 |
|
Item No. |
Dimensions |
||
|
Screw length |
Nut length |
Nut Ø |
|
|
LSp
|
LM
|
D
|
|
|
mm
|
mm
|
mm
|
|
|
1510/0,5.8.145.170 |
170 |
40 |
20 |
|
1510/1.8.145.170 |
170 |
40 |
20 |
|
1510/2.8.145.170 |
170 |
40 |
20 |
|
1510/2,5.8.145.170 |
170 |
40 |
20 |
|
1510/0,5.8.245.270 |
270 |
40 |
20 |
|
1510/1.8.245.270 |
270 |
40 |
20 |
|
1510/2.8.245.270 |
270 |
40 |
20 |
|
1510/2,5.8.245.270 |
270 |
40 |
20 |
1) Left
hand thread and non-standard leads upon request..
2) Additional ball circuits for extended load capacities are
also available.
3) Dynamic load capacity Ca : Permissable dynamic
axial load resulting in 1 x 106 rev. service life.
4) Please
inform about different preload.
The preload is set to Fpr max or at a minimum of 20 N. If Fpr max is higher than 20 N it can be set by Steinmeyer up to Fpr max. The maximum permissable axial load of Fmax is around 65 - 80 % of the preload.
The specified adjustment lengths take into account a certain overrun and can also be exceeded if required.
When ordering, information
on the installation direction of the nut, deviating preloads, required
tolerance classes and an appendix "P" for backlash-free execution
should be supplied.
Example: 1510/0,5.8.145.170
T3 P
If there is no other detailed information, the ballscrews are delivered grease lubricated with Klueber Staburags NBU 8 EP.